Přejdi na obsah | Přejdi na menu | Přejdi na vyhledávání

MSV
7.-11.10. 2013

International Engineering Fair

Gold Medal 2013 - registered exhibits

 

 

Secondary metallurgy VD / VOD-VI
Producer:  VÍTKOVICE HLAVY MACHINERY a.s., Ruská 2887/101, Vítkovice, 703 00 Ostrava
Exhibitor:  VÍTKOVICE, a.s., Ruská 2887/101, Vítkovice, 703 00 Ostrava
Location: Pav. P, stand 050
Description:
Vacuum degasser of VD/VOD-VIT type is one of the secondary metallurgy equipment in which molten metal in the pouring ladle placed in a hermetically closed vacuum tank is refined under deep vacuum. It can be used in mass-production of steel, where vacuum refining is followed  by continuous casting or  by casting to the mould,  and  eventually by subsequent vacuum arc remelting. In comparison with RH/RH-Ob/RH-KTB type  equipment, the advantage of this VD/VOD  equipment  is emulsification of treated slag with metal melt during the refining process, whereas this slag acts as a refining reagent.

SL-C350 IP55 30W10.6
Producer:  MARKEM - IMAJE S.A.S.
Exhibitor:  ONDRÁŠEK INK-JET SYSTEM  spol. s r.o., Nad Přehradou 2296, 738 02 Frýdek-Místek
Location: Pav. E, stand 013
Description:
SmartLase C series offers the right configuration for each industry, always providing a solution whatever the rate, size and substrate of the product (wide choice of lenses, scan heads and laser sources). SmartLase C series are designed for markets such as frozen food, chocolate confectionery and dried process food that need to code paper-based containers. SmartLase C series are designed to code on PET, reducing the risk of piercing containers, even lightweight thin-walled bottles.

ProTemp PTW 150-1 Controlled temperature water equipment for temperatures up to 150°C
Producer:HAHN Enersave GmbH
Exhibitor:HAHN Automation, s.r.o., Klostermannova 1000, 250 82 Úvaly
Location:Pav. G1, č.stánku 44
Description:
Water temperature control unit, which thanks to the innovative pumping system (multi-stage centrifugal pump), optimizing the control parameters and alignment of the ratio between the electric motor and pump can drastically increase the efficiency of the process of tempering.

Jet turbine engine TJ100S-125
Producer:  První brněnská strojírna Velká Bíteš, a. s.
Exhibitor:  První brněnská strojírna Velká Bíteš, a. s.
Location: Pav. V, stand. 037
Description:
The turbojet engine has been designed and manufactured as a driving unit with the thrust 1250 N, above all for unmanned air vehicles. The engine is a single-shaft conception with a single-stage radial compressor, annual combustion chamber, single-stage axial turbine and exhaust nozzle. The rotor of the engine is mounted on 2 ball bearings,  lubrication provides autonomous oil system. In the compressor suction, there is a  brush-less starter generator, which makes it possible to start the engine from the board network and generate energy during the engine run. Engine control is provided by digital control system.

Service Robot ROBOTUL® VERTICAL CLIMBER 02
Producer:  Technická univerzita v Liberci, Studentská 2; 461 17 Liberec, www.tul.cz;
Exhibitor:  Technická univerzita v Liberci, Studentská 2; 461 17 Liberec, www.tul.cz;
Location:  Expozice TU v Liberci, Pav. A1, stand 14
Description:
The exhibit ROBOTUL® Vertical Climber 02 is a functional sample of a service robot that solves in a unique way movement on smooth, respectively structured, vertical walls, especially of glass. The presented device represents a category of semiautomatic systems with partial autonomy. It easily deals with vertical movement in a chosen direction, to provide problem-free rotation and it allows overcoming the surface discontinuity and assembly holes. The device permits also movement on negatively tilted facades and offers relatively high load capacity. ROBOTUL® Vertical Climber 02 with additional technological superstructures is designed for a wall cleaning with minimal amount of liquid, for a dry cleaning, cleaning technologies and for implementation of inspection activities.

PU spiral hose "Master-PUR Performance"
Producer:  Masterflex SE, Willy- Brandt- Allee 300, D- 45891 Gelsenkirchen
Exhibitor: MASTERFLEX Česko s.r.o., Průmyslová 917, CZ- 348 15 Planá
Location: Pav. G1, stand  77
Description:
Master- PUR Performance: PU Suction/Transport Hose, extremely abrasion- resistant & vacuum- proof, seamless & totally smooth inner lining, antistatic & microbe- resistant, wall thickness min. 2,5 mm
World first !

Differential leak tester ATEQ F620
Producer:  ATEQ S.A.
Exhibitor:  ATEQ PL, Sp. z o.o., organizační složka
Location:  Pav. C, stand. 32
Description:
Leak tester F620 is detektor used to check the integrity of parts on the production line. It can be used for sample and audit testing. The detection principle is based on measurement of low diferential presure variation or presure drop between two parts, one to be tested and the other used as a reference. Use  in pressure and vacuum.Large range of leak measurement 50 Pa, 500 Pa, 5000 Pa.
New electronic module, new measurement module, new interface, new accesories. The latest leak testing technics and technology will garantee fasters and most accurate leak testing cycle.

Induction melting furnace I 03/13
Producer:  LAC s.r.o., Jiřího z Poděbrad 26, Hrušovany u Brna 664 62, Česká republika
Exhibitor:  LAC s.r.o., Jiřího z Poděbrad 26, Hrušovany u Brna 664 62, Česká republika
Location:  Pav. V, stand 31
Description:
metals (gold, silver, copper alloys) was developed in response to demand by goldsmiths for simple, compact and effective furnace. One of the main advantages is the possibility of casting by tilting the furnace (the tilting system is designed for single-handed operation). Due to the very rapid melting (1 kg Cu in 9 minutes) there is a minimum of burning molten material consequently low cooling water consumption and total electricity consumption for melting.

Sliding headstock automatic lathe K'MX 632 EVO
Producer:  TAJMAC-ZPS, a.s., Třída 3.května 1180, 764 87 Zlín, Malenovice, Česká republika, www.tajmac-zps.cz
Exhibitor:  TAJMAC-ZPS, a.s., Třída 3.května 1180, 764 87 Zlín, Malenovice, Česká republika, www.tajmac-zps.cz
Location: Pav. P, stand 39

 

H 800
Producer:  TAJMAC-ZPS, a.s., Třída 3.května 1180, 764 87 Zlín, Malenovice, Česká republika, www.tajmac-zps.cz
Exhibitor:  TAJMAC-ZPS, a.s., Třída 3.května 1180, 764 87 Zlín, Malenovice, Česká republika, www.tajmac-zps.cz
Location: Pav. P, stand 39

Rotary-linear motion converter
Producer:  KULIČKOVÉ ŠROUBY KUŘIM, a.s., Blanenská 1277/37, 664 34 Kuřim, T 541 102 273, M 602 585 933, www.ks-kurim.cz; ČVUT v Praze, Fakulta strojní, Ústav výrobních strojů a zařízení Ú 12135, Horská 3, 128 00 Praha 2, T 221 990 915, 224 359 330, M 605 2050934, www.rcmt.cvut.cz
Exhibitor:  ČVUT v Praze, Fakulta strojní, Ústav výrobních strojů a zařízení Ú 12135, Horská 3, 128 00 Praha 2, T 221 990 915, 224 359 330, M 605 2050934, www.rcmt.cvut.cz; KULIČKOVÉ ŠROUBY KUŘIM, a.s., Blanenská 1277/37, 664 34 Kuřim, T 541 102 273, M 602 585 933, www.ks-kurim.cz
Location:  Společná expozice KSK Kuřim, a.s. + Hestego Vyškov, a.s., pav. P, stánek č. 101
Description:
Rolling elements of the motion thread mechanism (MTM) consist of a system of spatially mounted revolving and adaptive pulleys, which are placed in the nut. These pulleys surround the threaded shaft. They are set into the thread and roll on the surface of the thread. Pulleys may have various shapes according to designed thread surfaces. This solution enables silent running, simple design, and possibility of regulation of MTM rigidity and preload of pulleys, possibility of choosing thread profile design, high reliability and long service life. MTM may also be applied to a high-pitch screw or to a screw with two opposite threads, which enables smooth reversing operation.

Multi-axis milling center HEM 500U
Producer:  Mikron Agie Charmilles AG, Ipsachstrasse 16, 2560 Nidau, Switzerland
Exhibitor:  Agie Charmilles, s.r.o., Dornych 54/47, 60200 BRNO, Česká republika
Location:  Pav. P č.stánku 105
Description:
HEM 500U: flexible, affordable, functional Milling solution
Flexibility, a compact and simple design, ergonomics and ease of use are the hallmarks of the new five-axis Milling machine from GF AgieCharmilles. Acronym HEM means "High Efficiency Machine" - a machine with high working efficiency, which is evident from the price-performance ratio and also on the machine size - performance ratio of this machine. Accuracy, flexibility and easy operation of this machining center provide excellent conditions for the production of components made of aluminum and steel, in both serial and single-piece production workshop.
Mikron HEM 500U offers unbeatable excellent view of the working area and easy access and loading the workpiece.
The HEM 500U with its new developed rotary tilting table persuades with competitive performance in terms of stiffness and versatility in its class. The newly developed solution of tilting table in the Y-axis gives an unique connectivity options and pallet automation systems without re-designing  the machine. This further increases the flexibility and utility features of the machining center. It is the ergonomic answer for the standard production of precision parts in prototyping with wideopening doors up to series from five workpieces pallet automation.
This functional and easy to use Milling solution comes with Heidenhain’s iTNC 530 control enabling production of highly accurate work piece contours while machining at high velocity.It matches perfectly with the machine, a reliable and sturdy five-axis Milling center for all kinds of “3+2” Milling jobs. The control’s uniformly digital design ensures high accuracy andsurface quality, as well as high traverse speeds.

Hybrid dressing system - hDD a cDD dressing tools
Producer: MEISTER ABRASIVES AG, Industriestrasse 11, CH-8450 Andelfingen, +420 602 369 109, milan.mihalcin@meister-abrasives.cz, www.meister-abrasives.com
Exhibitor:  MEISTER ABRASIVES AG, Industriestrasse 11, CH-8450 Andelfingen, +420 602 369 109, milan.mihalcin@meister-abrasives.cz, www.meister-abrasives.com
Location:  Pav.  P, stand 114
Description:
Hybrid dressing tools are characterized by high durability, stability and the unique characteristics of the dressing of grinding wheels. This specific bonds (the combination of ceramic and metallic bonds). The structure is porous dressing tools. Applications are available on static and rotary dressing tools. Dressing tools can be deployed on all the used grinding wheels.

MGC 5200
Producer: VÍTKOVICE MECHANIKA a.s., Ruská 2929/101a, 703 00, Ostrava, tel: 602 265 761
Exhibitor:  VÍTKOVICE a.s., Ruská 2887/101, 703 00, Ostrava, 595 951 111
Location:  plocha A, stand 001
Description:
MGC 5200 is container which is determined for transport and storage of CNG. It is used as gas storage for industrial applications, but it can be used as gas storage for households, or as gas storage and filling station for cars with CNG drive. An effective construction of MGC 5200 is able to transport up to maximum 5 200 Nm3 of CNG at 1CC standardized measurements. Compact and standardized dimensions and very high transport capacity of CNG are the biggest benefits for users.

MCU 1100V - 5X
Producer:  KOVOSVIT MAS, a.s., náměstí Tomáše Bati 419, 391 02 Sezimovo Ústí
Exhibitor:  KOVOSVIT MAS, a.s., náměstí Tomáše Bati 419, 391 02 Sezimovo Ústí
Location:  Pav. P, stand 123
Description:
The multi-functional 5-axis milling machine tool centre with a modular construction enables complex tooling of wide ranging work pieces from various materials. The modular nature of the tool centre provides the options to use spindle units with various properties, to define the size of tool magazines up to holding 360 tools using various clamping systems, to attach a lathe table and adjust the size of the rotary tilting table. The tool magazine is autonomously controlled and is characterized by strong rigidity, dynamism and the active thermal stabilization of the construction. The Faculty of Mechanical Engineering of the Czech Technical University in Prague and the Faculty of Mechanical Engineering of Brno University of Technology participated in the project

FLEXIVIT
Producer:  VÍTKOVICE POWER ENGINEERING a.s., Ruská 1142/30, 70600 Ostrava-Vítkovice
Exhibitor:  VÍTKOVICE POWER ENGINEERING a.s., Ruská 1142/30, 70600 Ostrava-Vítkovice
Location:  Pav. P, stand 050
Description:
Technology FLEXIVIT used to transform of waste heat from the flue gas piston engines of power units, the principle of an open Brayton cycle with indirect heating of the working medium. The main element of this energy cycle consists of a turbocharger, which is normally part of the internal combustion engine, which, together with the attached electric generator consists of turbine generator to produce electricity. The working medium is steam-air mixture that is in this energy cycle produced by mixing in a cycle of steam and air from the compressor of turbocharger. Working temperature of steam-air mixture before entering the turbine is achieved by heat of flue gas exiting from the gas engine power units. Steam-air mixture then enters the gas turbine of turbocharger, where expansion allows the transformation of its thermal energy to electrical energy, then is used to generate steam and chilled is finally discharged into the atmosphere

TPS/i
Producer:  FRONIUS International GmbH
Exhibitor:  FRONIUS Česká republika s.r.o., Ing. Jan Motloch, 272 111 090, motloch.jan@fronius.com, 724 775 588
Location:  Pav. A1, stand 25
Description:
The modular welding-appliance platform TPS/i shifts the boundaries that previously applied to welding technology. With it, users benefit from using individually customisable and upgradeable appliances that stand out for their high intelligence and extensive functionality. The TPS/i platform comes with a host of new developments that will significantly simplify welders’ daily work from now on.

AccuPocket
Producer:  FRONIUS International GmbH
Exhibitor:  FRONIUS Česká republika s.r.o., Ing. Jan Motloch, 272 111 090, motloch.jan@fronius.com, 724 775 588
Location:  Pav. A1, stand 25
Description:
The AccuPocket is the world’s first-ever MMA welding system with a high-performing lithium-ion rechargeable battery and a low overall weight of only 11 kg, giving users unprecedented freedom of movement in manual electrode and TIG welding. In terms of welding quality, too, AccuPocket outperforms many mains-only powered MMA welding units.

Bearing unit PLC 810-15
Producer:  ZKL Brno, a.s., Trnkova 2696/123, 628 00 Brno, 544 135 200, chief@zkl.cz, www.zkl.cz
Exhibitor:  ZKL Bearings CZ, a.s., Líšeňská 45, 628 00 Brno, 544 135 139, marketing@zkl.cz, www.zkl.cz
Location:  Pav. F, stand 082
Description:
Tapered roller bearing unit (TBU) with a plastic cage is a completely new product of the company ZKL. The bearing is designed for a new line of tram Škoda Transportation, designed for the city of Miskolc, Konya and Bratislava. Bearings have special seals and permanent filling of grease with life at least 1 million km. Development of bearings was realized with the support of the MPO TIP project FR-TI2/316. Design of bearing was optimized by FEM for reducing stress concentrations in rolling contact. The present innovation is fully in line with global trends in this area of rolling bearings.

Smart autopilot on EPOS airplane
Producer:  Evektor, spol. s r.o., Letecká 1008, 686 04 Kunovice, tel.: +420 572 537 428
Exhibitor: Vysoké učení technické v Brně, Antonínská 548/1, Brno 601 90, tel: 541 141 111
Location:  Pav.A1, stand 15
Description:
The Smart Autopilot is an innovative automatic digital flight control system providing significant flight safety improvements, while maintaining a high level of pilots’ control autonomy. In cooperation with Evektor, the system was installed into the futuristic sport aircraft concept SportStar EPOS. As a result of the development process, a significant synergic effect was achieved by the unification of the digital flight control technologies with a modern sport aircraft concept which is powered by an environmentally friendly electrical engine with characteristic low operating and maintenance cost.

Model pump NS 330 with spiral DZ-A0 330-HA 25.8-B
Producer:  SIGMA Group, a.s., Jana Sigmunda 79, 783 50 Lutín, +420 585 651 111
Exhibitor:  Vysoké učení technické v Brně, Fakulta strojního inženýrství, Energetický ústav, Odbor fluidníhího inženýrství Victora Kaplana;  Fakulta strojního inženýrství, Technická 2, 616 69 Brno, +420 54114 2343, hudec@fme.vutbr.cz, http://khzs.fme.vutbr.cz
Location:  Pav. A1, stand 15
Description:
The model of the HR-speed pump with suppressed cavitation at its optimum operating conditions - reducing the vibration and noise. From the model there are derived the horizontal and vertical pumps for pumping of the clean, slightly polluted and turbid water in the water industry, energetics, sewage and waste-water treatment facilities and irrigation systems in agriculture. The solution concept of the pump model - diagonal impeller with spiral.

Particle motion simulation device
Producer:  DSD-Dostal, a.s., Bystřická 38 ,751 14 Dřevohostice,  +420 777 776 065 info@dsd-dostal.cz, WWW.DSD-DOSTAL.CZ
Exhibitor:  VŠB-TU Ostrava, Centrum ENET, 17. listopadu 15, 708 33 Ostrava-Poruba, +420596994379, jiri.zegzulka@vsb.cz, www.vsb.cz
Location:  Pav.A1, stand 16
Description:
The exhibit registered for the competition for the gold medal is the application of the discovery of the hitherto unknown properties of particular mass realized in the Laboratory of Loose Materials at the VŠB-Technical University of Ostrava and applied in the form of a functional sample described in the subject of the patent for the invention “The method of simulation of kinetics movement of bulk solid particles and facilities to carry out the method” - EP09466006. The innovative works described the hitherto unknown property of particular mass leading to the definition of the particular mass state which is beyond the possibilities of the description of the hitherto known states; a group of inventions of very high level is coming into existence by elaborating this finding. These inventions make use of the majority knowledge and its impacts on the technical practice. The applications of the patent for the inventions that have been filed so far focus on the area of measuring the properties of particular mass and proposing new principles of machinery in the area of mechanical processes; the proposals of new methods applicable in industry, e.g. the method of energy-saving grinding, the methods of utilizing local extremes of dissipation works are significant. The patent method and the pattern equipment for “The method of simulation of kinetics movement of bulk solid particles and facilities to carry out the method” registered for the competition for the gold medal MSV Brno 2013 has had a number of applications leading to the proposal of new optimized designs of machinery, equipment and processes, while each new design and the described process can be, and usually is, patented again. The fundamental principles are elaborated in the form of direct cooperation with the company FITE in the framework of project MPO, FT-TA4/040.

GAMBIT MAGNUM
Producer:  GAMBIT LUBAWKA Sp. z o. o., ul. Wojska Polskiego 16
Exhibitor:  GAMBIT LUBAWKA Sp. z o. o., ul. Wojska Polskiego 16, 58-420 Lubawka, Poland, +48668870568, export@gambit-lubawka.pl, www.gambitgl.pl
Location:  Pav. V, stand 34
Description:
GAMBIT MAGNUM is a composite material used for manufacturing cut gaskets for flanges. High-performance aramid and mineral fibres mixed with nanofillers, and an exceptional HNBR caoutchouc composition forming a discontinuous phase make this product outrank the standard compressed-fibre sealing materials. Both the components and the technology of crosslinking give the whole structure unique characteristics. GAMBIT MAGNUM retains higher elasticity at elevated temperatures and has a greater resistance to media than the standard gasketing sheets. These characteristics render longer service of gaskets.

M2 cusing
Producer:  Concept Laser GmbH, An den Ziel 8, 96215 Lichtenfels, Germany
Exhibitor:  Misan s.r.o., Ke Vrutici 1795, 28922 Lysá nad Labem, +420325551440
Location:  Pav. P, č.stánku 136
Description:
M2 cusing machine is a metal laser melting system for production of parts made of stainless hot-work steel, titanium, aluminium and CoCr alloys, Inconel and precious metals. This additive technology system utilizes laser to melt metal powder added gradually. It can be used for production of detailed final components, parts with conformal cooling channels as well as cast prototypes. This technology can be used in automotive, aerospace, moulding, medical, dental and jewellery industries.
Innovation consists of optional quality management system QM Meltpool providing complex production diagnostics by means of scanning melting process with automatic report of possible structural faults of produced parts. This function is demanded especially in aerospace and medical industry.

Fully automatic very precise line laser scanner CMS106 integrated into motorised measuring head TESASTAR.m
Producer: HEXAGON METROLOGY s.r.o, Litvínovská 609,  190 00 Praha 9,  Tel: +420 272 680 830
Exhibitor: Hexagon Metrology Ltd., www.hexagonmetrology.com
Location: Pavilon F, stand. 39
Description:
CMS106 is a highly accurate, fully automatic, stripes laser scanner with several unique features.
By the integration into motorized measuring head TESASTAR-m, which can achieve up to 3024 positions with an accuracy of 0.001 mm, the system can scan even of very complex parts.
Zoom offering a three-level variable line width in the range of 24, 60 and 124 mm, management of laser scanning intensity in real time.
Laser scanning probe CMS106 provides 3D data of high quality and excellent speed: up to 2000 points per line and 50 lines / sec .
The laser scanner CMS 106 provides reliable and reproducible results in much less time and has a large detection angle ± 60 °.
Laser scanner CMS 106 provides reliable and reproducible results in much less time and has a large detection angle of ± 60 °, and even among machined surfaces. It is suitable for the measurement of almost any material including machined or polished surfaces extruded, forged, cast of  non-ferrous metal, sand cores, carbon fibre, plastics, clay, rubber, wood and ceramics.

PRINTER 3D FABBSTER C12/V2013
Producer:  SINTERMASK GmbH, EICHENBUHL 10, D-92331 LUPBURG, GERMA
Exhibitor:  AGI s.r.o., Električná 23, 91101 Trenčín, Slovensko, 00421327445272, ivanka@agi.sk, 0903440821
Location:  Pav.V, stand 112
Description: 
The exhibit is an innovative printer 3D fabbster derived from casette system C12. It includes therein by one year's experience of operating more than a thousand pieces from the production and customers. Innovation involves more sensor control process, innovated software amendment thermal stabilization process of printing and its individual components.

supraSchwank
Producer:  Schwank GmbH, Bremerhavener Str. 43, 50735 Köln, Germany
Exhibitor:  SCHWANK CZ, s.r.o., nám. Republiky 1, 614 00 Brno
Location:  Pav.V, stand č. 079
Description:
supraSchwank is the world's most efficient luminous heater that reaches radiant efficiency of up to 80,9%. This is enabled by highly heat-resistant radiant grid and special ceramic reflector insulation which prevents the wasting heat. Instead of radiation loss through air stratification below the ceiling, the heat is distributed directly where is needed (on workplace, employees, working tools).

 

You might be interested in

Highlights from companies MSV

 

Photo Gallery

VIDEO - MSV

Concurrently with

Transport and Logistics
9.-13.10. 2017


ENVITECH
9.-13.10. 2017

 

Find My Trade Show

Exhibition Centre